Kawasaki KLR Forum banner

1 - 3 of 3 Posts

·
Registered
Joined
·
1 Posts
Discussion Starter #1
Hi All - great site from what I can see so far. A friend of mine suggested that I get on here and I won't be disappointed.

I live in Vancouver, BC
Bought a 2004 with 32000 Kms on it
I have just ordered a shop manual so I can:
-fix an oil leak
- change the battery
- and more than likely change the oil and fluids - cold weather riding throughout the winter on the agenda
 

·
Premium Member
Joined
·
2,942 Posts
Hmmmm.

Welcome and congrats on your purchase.

- Oil leak? hopefully not from a cracked case at the oil drain plug.....

- cold weather riding = I'd consider installing a Thermobob. Information, Articles


....and my general, Top New KLR Owner Mistakes to Avoid list (developed with help of Paul, Tom and others here)


1) Oil drain plug overtightening: it is relatively common for people to overtighten the oil drain plug.....usually to stop a leak after the gasket/washer has inadvertently fallen into the used oil or left stuck to the bottom of the engine! best case is stripped threads, worst is a cracked case. Make sure the washer is in place and use a torque wrench Note; my manual says 17 ft lbs, Eaglemike recommends 15 ft lbs with his low profile drain plug which is what I use. Some Gen2 manuals specify 21 ft lbs but there has been no change in the plug or case which would affect the drain plug torque and people have stripped their drain plugs at this setting: beware!

- 2) Chain tension: many owners and some shops overtighten the KLR's drive chain; due to the long travel suspension and geometry the KLR needs more slack than other bikes people may be used to. If the chain is too tight you risk damaging the countershaft seal and bearing as well as possibly the wheel bearings along with premature wear of the drive chain and sprockets. Quick check; with the bike on the sidestand, you should be able to touch the chain to the bottom rearmost portion of the chain slipper but not the metal swingarm itself.

- 3) Speedo drive: it is common for people to post problems with their speedo after they've had the front wheel off. If you don't make sure the drive slots in the hub are aligned with the speedo drive tangs you risk bending the drive tangs and worse, breaking the hub. Time consuming to repair, expensive to replace, easy to avoid!

- 4) Oil Level: the factory KLR oil level sight glass is arguably too low....additionally some KLR's burn oil at various rates so it is imperative that the oil level is constantly checked. Luckily the sight glass makes this very easy to do. My suggestion is to keep the oil level at the very top of the sight glass with the bike level and to check it before every ride and at every fuel stop. The first failure from low oil levels is likely to be the cam bores in the head......and used KLR heads are getting difficult to find and are expensive. Keep an eye on that oil level!

- 5) Overtightening of other fasteners; similar to the oil drain plug there are a few other fasteners that cause significant problems if overtightened; the valve cover bolts are one such fastener - the manual calls up 69 inch lbs (NOT ft. lbs!) but Eaglemike suggests 55 in lbs which is a safer value. Another problem fastener is the footpeg mounting bolts; the factory nuts welded in the frame box are very thin with only 3 or 4 threads catching......these often strip out necessitating a repair. To avoid the problem, consider not using accessories that bolt to the bike using these bolts (i.e. centerstands) and torque them properly. I've heard that some manuals show 45NM (33 ft lbs) and some versions show 25 Nm (18 ft lbs)......I will suggest that the 33 ft lbs is a mistake and too much; I go with the 18 to avoid stripping the nuts and because this value falls in line with the recommended torque for generic 8mm fasteners in the manual. Safety wiring the bolt heads is also a wise precaution as loose bolts take the threads out quickly.

- 6) Throwing away the tube when changing the oil filter. People often mistakenly toss the metal tube that is inserted in the oil filter when they throw the old filter in the trash....make sure it's there and put it back in the right way.

- 7) attempting a counterbalance lever (doohickey) adjusting bolt adjustment without first ensuring the lever and spring are both intact and the spring has tension. Failure to do so can introduce a catastrophic amount of play into the counterbalance chain system.

-8) Not checking fasteners for proper torque at least at every oil change. Especially foot pegs and sub-frame bolts. The fasteners that Kawasaki put in place are adequate, but once torque falls below spec vibration can loosen the fastener. A loose fastener will quickly fail if it is under load.

-9) Not properly oiling your air filter. I prefer foam filter oil but regardless of what you choose to use, ensure your foam filter is thoroughly oiled and seated or dust will destroy your engine.

- 10) Not checking to make sure your clean side airbox drain tube and plug are present and accounted for; This tube often gets pulled off (some people shorten it to help with this) and if it does your engine will ingest non-filtered air which can dust out and destroy your engine. ….while you’re in the area, also check to make sure your header to mid pipe junction is tight otherwise you can melt your airbox causing much the same problem.

cheers,
Dave
 

·
Registered
Joined
·
5,567 Posts
I'd just add . . . to # 5 above, "Overtightening of other fasteners . . . ," oil filter cover bolts. Torqueing these jewels will NOT help sealing pressurized oil in the filter cavity anyway, because . . . the oil filter O-ring performs this function, NOT the tightness of the cover mounting. Easy to strip the threads (maybe, even break the bolts) from over-zealous wrenching.

Yet, if you DO strip an oil filter cover bolt thread, or break a bolt, one bolt alone will hold the cover in place and seal the pressurized oil 'till a proper repair can be made. Better, certainly, a PAIR of redundant operational fasteners.
 
1 - 3 of 3 Posts
Top